An engineer comparing two foams on their data sheets sees density, absorption and thermal conductivity measured in a laboratory. The part they design will live behind a cabin lining, inside a machine or in a filter housing. Which of those numbers will still matter there?
We start every material decision with that question. Our engineers first define what the part has to withstand, how the installer will fix it, how it will behave in production and what the customer has to certify. Then they compare materials.
Most parts carry several functions at once. A cabin lining absorbs sound, slows heat flow and has to cope with condensation. A machine enclosure panel absorbs sound on the inside and blocks it on the way out. With every added function, engineers have fewer materials and constructions to choose from.
Pinta works independently of any single material or chemistry. We buy from several producers and convert their foams, fibers, mass layers, films, foils, fabrics, adhesives and inserts into components, and our engineers combine them when one material covers only part of the job.
Read material families by their structure
Open-cell foams, such as melamine resin, polyurethane and polyimide foams, have connected pores. Sound enters those pores, and friction against the cell walls turns acoustic energy into heat. Air and water vapor travel through the same pores.
Closed-cell foams, such as cross-linked polyethylene or elastomeric foams, hold gas in sealed cells. They take up little water, insulate against heat and condensation and seal joints. On their own, they absorb little sound, so manufacturers perforate or profile their surface when a part needs absorption.
Mass layers reduce the sound that passes through a wall, and the reduction grows with their surface mass and with frequency. Films and foils keep moisture out and protect surfaces, and they also change how the foam behind them absorbs sound. A designer who chooses a facing therefore makes an acoustic decision as well.
Each family has its strengths. Melamine resin foam weighs around 9 kg per cubic meter and resists flame through its chemistry. Polyimide foam keeps its properties across a wide temperature range and produces little smoke when it burns. Closed-cell foams cope with wet environments. The engineer’s task is to match those strengths to the application.
Follow the moisture as well as the heat
Engineers trace many cases of insulation that performs well in the laboratory and loses performance in service back to water. Warm, humid air reaches a cold surface, cools below its dew point, and water condenses inside or behind the insulation. Wet insulation conducts more heat, weighs more and absorbs less sound.
Engineers control where that water goes through the order of the layers. A vapor control layer on the warm side limits how much moisture enters. A water-resistant, vapor-open layer on the cold side lets it leave. Drainage paths and ventilation carry away the rest.
Aircraft engineers face this principle in its strongest form. At cruise altitude, the fuselage skin sits far below freezing, and cabin moisture collects behind the lining as frost and later as meltwater. For an aircraft manufacturer, we supply a lightweight kit that combines acoustic and thermal insulation with moisture drainage, described in the case study Managing cabin moisture
Aircraft manufacturers also certify insulation for fire. Under CS 25.856 and FAR 25.856, they test thermal and acoustic insulation for flame propagation, and their suppliers trace every material from raw stock to finished part.
Design for the frequency range
Sound is a spectrum. A foam that absorbs most of the sound at 2,000 Hz can do little at 100 Hz.
Porous absorbers work best when their thickness reaches about a quarter of the wavelength. At 1,000 Hz, that means about 9 cm. At 100 Hz, it means close to 90 cm, more than most installations allow.
For low frequencies, engineers therefore add mass, build resonant constructions or move the material to a position where it can act. They start by measuring which part of the spectrum carries the problem.
Engineers who protect satellite payloads face the frequency problem at its limit. During lift-off, the sound pressure inside a payload fairing reaches around 140 dB, with much of the energy at low frequencies, and every kilogram of protection reduces what the launcher can carry. Our lightweight foam components for the payload area answer that brief; the case study Sound protection at launch describes them.
Combine layers when the task has two parts
Around a noisy machine, engineers usually need two acoustic functions. An absorber inside the enclosure keeps sound from building up between the walls, and a barrier in the walls reduces what passes through to the people outside. When designers use a barrier alone, sound builds up inside, and the enclosure loses part of its insertion loss.
Our PROSPEC Composite joins both functions in one panel: sound-absorbing WILLTEC foam faces the source, and a vinyl noise barrier blocks the path outward. In practice, sound escapes through ventilation slots, cable entries and service doors, so engineers design lined ducts, seals and gaskets together with the panel.
Regulators set the target for industrial noise. In the EU, employers must act once daily noise exposure reaches 80 dB(A) and keep their workers below the exposure limit of 87 dB(A). Engineers therefore specify an enclosure from what the operator hears at the workstation.
Manufacturers of specialty vehicles meet these tasks in the cab. Operators of agricultural, forestry and construction machinery and cranes can spend a full shift there, surrounded by heat, noise and vibration. Manufacturers of these vehicles often ask for a cab lining that joins a thermal layer, an acoustic layer and a facing people can clean, precut for the assembly line.
Account for vibration, temperature and fixing
In HVAC equipment, manufacturers expose insulation to vibration and changing operating conditions. On refrigerant and chilled-water lines, installers need closed-cell insulation with sealed joints to keep condensation off the outer surface. In ventilation boxes, compressors, hoods and casings, manufacturers need acoustic linings that stay in place through years of vibration and keep fibers out of the airstream.
Engineers should choose the fixing as carefully as the insulation. Every adhesive has its own temperature range and aging behavior, and a layer that loosens under vibration loses both its acoustic and its thermal contribution. We specify the adhesive or mechanical fixing together with the material and test them as one construction.
Balance filtration against airflow
In filtration, designers pay for every gain in capture with pressure. A denser medium or a thicker layer holds more particles and gives activated carbon more contact time with odor molecules, and the fan then has to overcome a higher pressure drop.
With activated-carbon foam media, our engineers tune that balance through porosity and carbon type. Customers replace filters as consumables, so every element in a long series has to perform like the first one. We treat media consistency and the assembly into housings or sleeves as part of the specification.
Test the construction you will build
Engineers choose each test for one question. They use a Kundt’s tube to measure absorption on a small sample at normal incidence, which helps them compare materials early in a project. In a semi-anechoic chamber, they isolate a source and measure what a machine or a component radiates. With tensile tests, they check how a material and its bond behave under load.
We run these tests in-house and work with external laboratories on fire, smoke and aging tests when an application requires them.
Keep the tested configuration with every result: grade, thickness, facing and mounting. The people who review a design then see which construction the evidence covers, and they know to review it again when a layer or a fixing changes.
Bring the task to the first conversation
Engineers start a project better from a precise problem than from a material preference. A frequency range, an operating temperature or the point where condensation forms tells the engineer what to compare.
Bring us the place the part will occupy, the conditions it meets there, the requirements you have fixed and the choices still open. Our engineers will propose materials and constructions, prepare samples and agree with you on the tests that show whether the part does its job.
Discuss your application requirements